![]() ![]() HP-2 BIO is a high performance cold mix binder for use in the most demanding asphalt or concrete pavement maintenance or pothole patching applications. HFRS-2 is an anionic, rapid setting, high float emulsion. ![]() This emulsion is used in chip sealing and plant mixing. HFMS-2 is an anionic, medium setting, high float emulsion. In addition, HFE-300 can be used in stockpile mixing. Along with HFE-150, this emulsion is used in cold plant mix and mixed in place. HFE-300 is an anionic, medium setting, high float emulsion with a very soft penetration base. This emulsion is used in cold plant mix, mixed in place and less frequently chip sealing. HFE-150 is an anionic, medium setting, high float emulsion. In addition, EA-300 can be used in stockpile mixing. Along with EA-150, this emulsion is used in cold plant mix and mixed in place. This emulsion is used in cold plant mix, mixed in place and less frequently chip sealing.ĮA-300 is an anionic, medium setting, high float emulsion with a very soft penetration base. The product has also seen use in mixing grades when dense graded aggregates are used.ĮA-150 is an anionic, medium setting, high float emulsion. Polymer Modified versions are used to improve chip retention and higher traffic areas.ĬSS-1 is a cationic, low viscosity, hard penetration emulsion typically used for tack coats, prime coats and fog seals. These emulsions are primarily used as chip seals and are spray applied with the chip (aggregate) applied immediately after spraying. ![]() A micro-surfaced surface is typically opened to traffic in one hour or less, sometimes in less than 15 minutes.Ī rapid setting emulsion designed to react quickly with aggregate. ![]() Some slurry emulsions are Polymer Modified, while all micro surfacing emulsions are Polymer Modified. Micro surfacing emulsions can be placed at greater thickness than a slurry emulsion. Slurry materials are placed at the thickness of the aggregate and designed for a quick return to traffic. Quick setting emulsions are designed for slurry and micro surfacing applications. This emulsion is used as a prime to penetrate surfaces before another treatment. This emulsion is used in chip seals and less frequently, hot and cold pant mix.ĪE-P is an anionic, medium setting very soft base penetration emulsion. In addition, AE-200 and AE-300 can be used in stockpile mixing.ĪE-90 is an anionic, medium setting, high float emulsion. Along with AE-150 and AE-200, this emulsion is used in cold plant mix and mixed in place. This emulsion is used in cold plant mix and mixed in place.ĪE-300 is an anionic, medium setting, high float emulsion with a very soft penetration base. In addition, AE-200 and AE-300 can be used in stockpile mixing.ĪE-3 is an anionic, medium setting, high float emulsion with a very soft penetration base. Along with AE-150 and AE-300, this emulsion is used in cold plant mix and mixed in place. This emulsion is used in cold plant mix, mixed in place and less frequently chip sealing.ĪE-200 is an anionic, medium setting, high float emulsion with a soft penetration base. This asphalt product is used as an emulsion base and in blending of other PG asphalts.ĪC-7 is an asphalt blended to meet 700P viscosity and 100-160 dmm penetration.ĪE-150 is an anionic, medium setting, high float emulsion. This asphalt product is used as an emulsion base, in roofing applications and in blending of other PG asphalts.ĪC-20 is unmodified asphalt product, approximately 2000P viscosity, used for hot mix asphalt, emulsion production or further modification for higher temperature paving grades.ĪC-30 is unmodified asphalt product, approximately 3000P viscosity used for hot mix asphalt, emulsion production or further modification for higher temperature paving grades.ĪC-5, approximately 500P viscosity material, is a high penetration range asphalt, typically also meeting requirements of a 150-200 dmm pen. This product has many applications including roofing, emulsions and blending.ġ50-200 Pen is a high penetration range asphalt, typically also meeting requirements of an AC-5, approximately 500P viscosity material. These SDA Bottoms are asphaltene rich resulting in typical properties of high softening point (212F+) and low penetration (typically 0 dmm) depending on the operating severity of the SDA unit. 0-10 Pen is produced from SDA (Solvent Deasphalting). ![]()
0 Comments
Leave a Reply. |